Showing posts with label Turning. Show all posts
Showing posts with label Turning. Show all posts

Saturday, March 5, 2011

Wood Turning Projects - Three Ways to Dress Them Up




Wood turning projects are a great way to learn new skills and to refresh old ones. They generally come with instructions from start to finish and hopefully with lots of pictures to give further guidance. However, the very nature of wanting to learn a new skill determines that the project needs to be repeated several times until the skills are developed. Often it is the case where the first is fascinating, the next couple are fun, and fourth is a challenge and rest are boredom but should be done. Since most of us who turn are hobbyists, boredom can be a killer to the craft. Thankfully, there are three simple ways to dress up a project, each or which may add its own challenges and interests.





First there is the obvious method of adding beads and coves. While it may seem like a simple solution to boredom one needs to ask where each bead or cove goes and whether it "works" with other beads, coves, straights and curves. If it goes on a handle does it make the handle more or less comfortable to use? Are there artistic reasons for placement or utilitarian ones such as distinguishing one tool from another while it is on the bench amidst the shavings? Adding beads and coves to spindle woke is so common that it is good practice for all spindle turning but face plate projects should not be neglected either. One bead at the rim of a bowl may give it an elegant look while a fully beaded surface will change the grain appearance strikingly, particularly in a broad grained wood like oak or ash.





Second one might add a line of color with burning or wood displacement. To burn a line on a rotating piece of wood one first suspends a thin wire between two wooden handles. Holding the wire without handles is asking for burned, cut or removed fingers while using the handles renders the activity safe. As the wood rotates at good speed it is first grooved slightly to prevent the wire from slipping as it is held in the groove. Pressure is applied by pulling the wire taut between the handles and friction causes a burn line to form. The depth of color can be controlled with additional pressure or the duration of the burn.





Wood displacement adds a line of color by actually transferring a bit of wood from one piece to the next and tends to work best on faceplate work although it can be used on spindles. It also works better with dark woods being used to color light ones. For instance if a bowl of maple is turning on the lathe, a thin piece of rosewood about 6 inches long and 1 inch wide but only 1/16" thick may have its edge brought to the spinning wood. Under a bit of pressure a bit of the rosewood will actually be transferred to the spinning maple. The band may be darkened by holding the rosewood in place a bit longer and broadened simply by moving it left and right.





Third is adding color to the wood. For some this is a shock under the belief that wood turnings should always be left natural, but people have been coloring them since turning started. Color may be added easily with felt markers while the wood turns or is stationary. The varieties of paints and stains available are amazing indeed. Leather dyes should not be overlooked. They use an alcohol solvent that will not raise the grain the wood, apply and dry quickly, and allow the grain of the wood to show through. Again there is a wide variety of colors available and they all mix well to give infinite choice.





Each of these methods and many others allow for adaption of wood turning projects to make them into signature pieces for a turner while learning a variety of techniques and style without the boredom of undue repetition.


Tuesday, March 1, 2011

Wood Turning Gifts - Hidden Money In Your Hobby




The calendar pages are turning. There is a birthday, anniversary, or special event coming up. Out comes the wallet and off the store you go in that awkward search for something affordable but special, unique but available, heart felt but not too sentimental. On the other hand, you may be a wood turner and the whole story changes.





An opportunity has arisen for one of your special pieces to find a new home. Somewhere on one of those shelves at the back of the work shop or in a box under the work bench, resides a wood turning for a friend or relative.





Most turners go through a progression of giving. The first attempts are amazing only to people who are surprised you could make anything at all, something like the dancing bear in the Russian circus. It is not so amazing that the bear dances well but that the bear dances at all. Everyone needs to keep a few of those first turnings for the sake of humility or at least later to realize how far you have come.





Then come turnings with reasonable lines, good sanding and an adequate finish. Some of these are given or sold to co-workers or are snatched up by spouses and children. There may be a phase of pen turning or the making of other small craft in the thought that this hobby might make money. However, after buying a new tool or so, it begins to feel like work and more esoteric turnings start to come off the lathe. A couple of craft shows sell a few pieces but most realize that full time turning is hard work.





So the pieces start to pile up. How many salad bowls does a family need, after all? Boxes hide some great turnings with wonderful lines and amazing patterns. Then Christmas makes its way around the yearly corner and you get together with your spouse and say things like, "Well, one of the kids might like this one." or "Does this piece of oak burl not remind you of Ed's nose? He has to have it." One by one, off go the pieces to new homes.





I think of this as the hidden returns of turning. First there is the satisfaction of having made a nice piece. Second comes the knowledge that the piece fits the person who receives it. Third is the knowledge that this unique gift is handmade in a world that does this less and less. Fourth is the financial reward of the unsold piece. For instance, ignoring birthdays and such for a moment, think of giving five turnings each year for five Christmases. Assume those turnings took the place of gifts averaging fifty dollars each. That is one thousand, two hundred fifty dollars earned by the hobby less expenses. Even if the expenses reached an unlikely two hundred fifty dollars, this is still a one thousand dollar profit. This is not bad for hours spent having a lot of fun.


Saturday, February 26, 2011

Turning Balls on a Lathe




Lathe work is so fun and exciting! If you're looking for a new woodworking project, consider turning some balls. It's fun to do and you can thoroughly entertain your children with this project. There are lots of things that you can do with turned balls. You can create decorative accents for vases, mobiles, a marble set for the kids, use them to create stems on handmade wineglasses, cabinet and drawer knobs, a working universe model, or create a handmade wine bottle stopper; the possibilities are really endless! Just use your imagination and think of all the crafty things you can do with wooden balls.





First you need to choose the type of wood that you will use. Basically, the harder the wood, the less indention you will see from the wood turning lathe attachment. The wood is held in place by a circular mechanism, so sometimes you will get a circular indention on one or both ends of the ball. Some lathe attachments don't mark up the balls as much as others, but really it depends on the type of wood that you use.





Start off with a center mounted block of wood. Use a gouge tool to get started and skew chisel to turn your block into a smooth cylinder. Be especially careful with the skew chisel, as it is considered to be very dangerous. If this is your first time using one, go very slowly and wear protective clothing and face protection. Skew chisels can easily dig into the wood and spring from your hand. Review the proper techniques for using a skew chisel before you begin. Practice before you turn on the lathe. The skew chisel should be very sharp and produce a long thin ribbon of wood when you're doing it correctly. You may have to attempt to create your cylinder several times until you really get the hang of the skew chisel.





Use a caliper to measure the diameter of the cylinder, making sure that it is the same all the way around. Then turn the caliper ninety degrees and mark the cylinder for the width of the ball making sure that it is exactly the same as the diameter. Measure for the center of the wood section that is to become your ball. Mark it with a pencil all the way around.





Measure half-way between the outside boundary marks and your center line. Use the pencil to mark this point so that the center of the cylinder is now divided into three sections. Use a gouge tool to cut from these new lines down to the boundaries, sloping out at forty-five degrees. Continue to work your way down so that the cylinder becomes more and more like a ball trapped between two blocks. You may need to remark your center line at this point.





Cut the ball loose and use a ball drive to hold the ball steady. Mount it with the center line vertical. Work your way around smoothing as you go. You can look for shadows to spot areas that aren't perfectly round yet. Take the ball off, rotate it so that the center line is horizontal, and repeat the smoothing process. Use fine grit sandpaper, rotating the ball ninety degrees again and again until the ball is smooth.





This technique is used for making balls. You can use the cylinder technique to create cylinders, dowel rods, or dowels of custom diameter. Remember to be safe!


Three Tips For Using a Wood Turning Lathe




If you learn the right way to use a wood turning lathe, it will soon become one of your favorite tools. Here are three important tips for using a lathe. They're applicable to all projects and you should keep them in mind whether you're turning a big, thick table leg or a delicate candlestick.





Good Projects Start with Good Wood





Before you even think of starting a wood turning lathe project, double-check the quality of the wood you're using. Using the right kind of wood is important, but that only one consideration.





You need to check the wood carefully to be certain it's the right size. Remember, you may lose a portion of the piece's top and bottom. That means you'll want to use pieces that are slightly longer than the project requires. There's nothing more frustrating than turning a great piece and then finding that you just can't use it.





You'll also want to inspect the wood carefully for quality. If you find deep scratches or cracks in your wood, you may end up with a final piece that will fall short of your quality standards. Check your wood for appearance, as well. Some pieces may have slightly discolored areas or grain patterns that just won't look right when you're done.





Using the Right Tool for the Job





A particular project may call for the use of a wood turning lathe, but that doesn't mean that any lathe will do. This fact becomes quite clear when you witness someone "biting off more than he or she can chew" by trying to handle an oversized piece of wood in a smaller lathe.





A pen lathe is great for a number of different jobs, but it won't be up to task for bigger projects. Likewise, smaller lathes may offer more precision and control than larger ones, making them ideal for small projects. Step back and evaluate both your project and your equipment. Are they really a good match? You should be able to answer that question in the affirmative without hesitation.





Your Hands and Eyes are Worth More than a Great Table





Every single project involving a wood turning lathe is serious. That's because you're using powerful equipment that has the potential of hurting you if not used correctly. "Safety first" may seem like a worn-out cliche, but it bears repeating when it comes to lathe work.





Be certain your wood is properly placed and is snugly fitted into the lathe. Use all necessary protective gear. Never touch a moving piece of wood with your hands--it only takes a few moments for the machine to come to stop. Don't remove a piece of wood until you've flipped the power switch to "off."





You may be excited to finish your project in record time, but it doesn't make sense to trade your safety and well-being to save a few minutes. Take the time and care to keep yourself safe.


Friday, February 25, 2011

CNC Turning Process - An Overview




CNC Turning process is a simple method of shaping a metal or wood on a lathe. It is a machine tool that spins or turns a block of material to achieve rotational symmetry in a machine shop. Turning can be done manually or using a CNC machining. The computer numerically controls CNC machine. A typical CNC machining center is designed to remove material using a rotating cutter that moves laterally to a work piece mounted onto a table or fixture.





In the CNC turning process, a piece of material is rotated on the lathe and a cutting tool is traversed along two axis of motion, transverse or longitudinal. The process is done in a machine shop. The cutting tool is used until the required depth and dimension is achieved. Turning can be on both sides, inside or outside as per the needs and specifications. The rotation occurs at the turning center that enables control of tool motion through computer programs that use numeric data. Parts that are too large to balance and cause difficulty in rotating around one center point, can be worked on a machining center featuring a U axis. The turning length is about 1000mm between centers and has a drive power and speed range up to 46kW and 4,000 revolution/minute respectively.





CNC turning process cuts the metal into various different shapes ranging from plain surface, taper ends, contour, and filter to radius profiles and threaded surfaces. These cut and turned metal pieces are used to create shafts, rods, hubs, bushes, pulleys and much more. Many industries also use it for fabricating parts and materials that have circular cross section. The process applies well to the most rigid materials that can be controlled exclusively with the software program tooling. The process does reduce the cost of production but on the other end, it limits the design flexibility.





CNC turning machines are said to deliver components at a faster production rate with optimum manufacturing accuracy. The automation of the CNC turning process allows reaching tight dimensional tolerances in every piece. Other advantages are high level of parts consistency or uniformity, achievement of optimum cycle times for all components and faster execution of larger volume. As machines have brought a revolution in the industrial world, new technologies provided by emachineshop, boost the use of metal products.


Tuesday, February 22, 2011

Lathe Equipment For Spindle Turning




The lathe motor drives a spindle to which the timber to be turned is attached by means of a range of equipment/accessories. The spindle, in the headstock of the lathe, is hollow with an internal taper which accepts some driving devices; other devices can be screwed onto the spindle which is threaded on the outside. The size of the taper and thread varies between lathes so it is important that the user knows these sizes when buying the various devices for fixing the timber to the lathe.





The tailstock houses a hollow barrel which also has an internal taper, usually, but not always, the same taper as in the headstock. This barrel accepts the tail centre which supports the timber during spindle turning.





The headstock spindle and the tailstock barrel should be hollow all the way through so that devices fitted into the tapers can be tapped out with a round bar when necessary. If the headstock is not hollow then it is advisable to use a thread protector on the headstock; unscrewing this will eject any device in the taper. Tail centres can be removed by placing a flat piece of metal between the centre and the body of the tailstock and then winding back the barrel with the tailstock handwheel.





There are several types of drive centre for spindle turning. These do not grip the wood so there needs to be support from a tail centre. Two or four prong drive centres are usually supplied with a lathe. These consist of a centre point with two or four driving blades mounted on a tapered shank. The drive blades can be located in the timber by saw cut grooves or the drive centre can be driven into the timber with a wood or plastic hammer. The Stebcentre is a more advanced type of drive centre; the centre point is spring loaded and this is surrounded by a circle of fine points, the wood is driven onto the Stebcentre by turning the tailstock handwheel until the points engage. For turning light pulls there is a stepped drive which locates in the previously drilled blank. Conical drives of various sizes are also available, these usually screw onto the headstock spindle. A drive with an internal square taper, for turning lace bobbins, is also available. There is an increasing range of mandrels and accessories for pen making.





When the timber is driven by one of these devices it has to be supported by a centre in the tailstock. When a dead centre is fitted the timber rotates around the point of the centre causing friction and the generation of heat. To minimise this effect it is necessary to lubricate the point of contact with wax. A much better device is the live or rotating centre whose point is mounted in bearings which allow it to rotate with the timber thus eliminating the need for lubrication. Tail centres come in a variety of sizes some with the point incorporated in a cup centre which reduces the risk of splitting the timber.





The tailstock can also be used for housing a taper mounted chuck, such as a Jacob's chuck, for drilling the timber as it turns. A hollow tailstock also acts as the guide for a long hole boring bit which is necessary when making table or standard lamps.





The tool rest is fitted in a banjo which can be moved along the lathe bed and at right angles to it. The tool rest can move up and down in the banjo and can rotate within it; both banjo and toolrest can be (and must be) locked when in the correct position. All lathes are supplied with one, toolrest - some with two. For best control of the cutting tool the tool rest should be as close as possible to the timber. When very small items are being turned (e.g. the baby in a mother 'n babe lace bobbin - about 20mm long) the standard tool rests are too long, so there is a need for a smaller rest. An engineering friend may be able to make one, or a standard rest can be cut to size or Sorby's system may offer a solution.





The height of the lathe is important in the interests of safety and ease of use. Ideally the centre line between the head and tailstock spindles should be at the level of the turners elbow. Some lathes have a height adjustment others do not, so it may be a matter of making a platform, of suitable height for the lathe - or the turner - to stand on.


Monday, February 21, 2011

Wood Turning Lathe Devices




Wood turning can be a fun filled experience when a right kind of tool is employed. It will be truly rewarding and an addictive experience for the wood workers. You can do wood working process at ease and even modifying any furniture present at home with these devices. The real joy in making or modifying your furniture can give a real sense of happiness. It also saves a lot of money and time for you. It can be a learning experience by which you can master the art of handling the tool.





Lathe machines have become trendy in the recent days. Be careful in selecting the right kind of device for your application. If you pick up a wrong tool, then you might end up in frustration by not getting proper output. You might have wasted huge amount of money on a wrong tool which is absolutely useless. There are tools available in various sizes. Right from pen type lathes to huge machines, they come in huge sizes suited for different types of applications. A 11 inch lathe will have the capacity to turn a wheel that has diameter of 11 inches.





The other factor to be considered in woodworking lathes is the center measurement. This number determines the maximum length of the materials required that can be mounted between the head and tailstock. Their parts might or might not include leg or table stand. This will help you to get proper elevation while working with these devices. Proper height will improve efficiency of the operators.


Sunday, February 20, 2011

Points To Consider For Wood Turning Lathe Devices - Part 2




The most advanced versions of these tools are expensive. Make sure the device will accept the readily available tools and accessories. Choose the additional accessories so that it will fit the size of the machines. It is important to note down the head stock spindle thread and the tail stock taper material sizes.





If the device comes with a leg or table, make sure it is of correct height and elevation. This helps in smooth functioning of the device. Workers will be in a better position to extract the best out of these lathe tools. An important tip to remember is that the center of the spindle should lie at the height of your elbow. The height should be adjusted to the individual heights. A stand built will solve these problems for the beginners.





It is recommended to get some expert advice before you buy the device. Someone who has been working with these tools for a long period of time will be able to give valuable advice on the kind of selection of tools.





Consider the safety measures that you have to take before start working on these tools. It is even the responsibility of the manufacturer to design the tool in such a way it ensures safety under all circumstances. Do not be hurry in choosing the device.





Make a note of the warranty features and the terms included for that. The expert advice will be of maximum help under this circumstance. Make sure you buy the right kind of tool to execute your task.


Saturday, February 19, 2011

Wood Turning - After the Basic Tools, What Then?




Wood turning is an old craft. In fact, Egyptian pictures on the sides of pyramid tombs indicate a history of at least three thousand years. Most of the basic tools such as cutting tools and the wood lathe itself have not really changed since then. At the same time the tool catalogues are full of a bewildering array of accessories, add-ons and gadgets. Here are some thoughts on what may make turning more enjoyable.





First of all there are the myriad numbers now of project parts. In days gone by, people either made some of these such as potpourri covers or had them made by other craftsmen. Now they are readily available from various suppliers. Obviously, if you wish to make a pen, you will need pen parts. Simply buy project parts from reputable dealers and you will be fine.





Less obvious are some of the accessories, including safety items. One of the first things to buy is a face shield. Most woodworkers will already own and use safety glasses but there is a fundamental difference between a wood lathe and most other shop power tools. Most of our tools have rotating or otherwise moving blades that cut through a piece of wood that is advanced to them. Wood lathes hold wood and move it toward us while we use sharp tools on it. If the wood is released for some reason it can fly out and hit a turner in the face. While this is rare, it does happen. What is more frequent as a turner advances in knowledge and begins to use more decorative wood with bark inclusions and other bits, is that shavings, bark and wood chips are thrown at the turner. A face mask is almost a requirement.





To go along with the face mask is the sanding equipment and dust mask that is needed. A simple piece of sandpaper will work for a long while, but sanding pads powered by electric drill or some other means speed up work. They also kick up a lot of dust and lungs should be protected with a dust mask. Look for one with an N95 safety rating to protect your lungs.





While chucks are a topic in themselves, many wood turners like to use four jaw chucks to hold wood on the lathe. While these are not necessary, they are very convenient for a lot of uses. Get a good one. They tend to hold large and heavy blocks of wood that should not be allowed to fly out from the lathe. Remember that these are very young in the history of the craft and may cost more that some beginner lathes.





One of the great additions to the turner's arsenal in recent years has been the use of cyanoacrylate glues, sometimes called super glues after one of the first marketed to the general public. They come in various viscosities or thicknesses. Many turners will find plenty of uses for both the thin and medium types. They are handy for holding some work, attaching pen or other project parts, filling cracks that would otherwise spoil a piece of work and the list goes on. These are available from most woodturning and woodworking suppliers.





While there are other always other things to consider purchasing in the never ending game of tool buying, once the basics are on hand, this age old craft is a great provider of all kinds of enjoyment. Even though many new tools and accessories may be bought or dreamt of, woodturning only needs the basics for good craft.


Wood Turning Safety - Essential for Enjoyment




The practice of wood turning involves throwing wood at one's face and stopping it with sharp tools. While this is said somewhat tongue in cheek, it is none the less true. It is to hoped that the method of securing the wood on the lathe will be sound but it also true that there is less than sound wood to contend with at times, not to mention the shavings that often come directly at the turner's face and which may be accompanied by splinters of wood and pieces of bark. Obviously some rules for safety need to followed. While most are simple common sense that does not mean that all wood turners everywhere follow them. In fact, the first and most important rule of safety is simply to use common sense. If something looks dangerous it likely is. Do not do it.





1.Know your lathe well. Read the manual and learn all the parts and what they do.





2.Protect your eyes, ears and nose. Use a full face mask for turning, hearing protectors when the noise is loud, and a good dust mask for sanding.





3.Keep dangling things away from turning wood which could catch them and pull you in. Long hair should be tied back and do not wear loose clothing, jewelry or other loose objects.





4.Use an appropriate speed for the wood on the lathe. If the lathe shakes, slow it down until balance is achieved.





5.Keep all belt guards in place and make sure that the tail stock and tool rest are tight. Check them periodically as you turn.





6.Rotate the wood by hand to ensure it clears the tool rest and lathe bed before turning on the lathe.





7.Turn off the lathe before adjusting the rest.





8.Maintain a firm but comfortable grip on the tool at all times.





9.Do not reach over turning wood. Shut the lathe off first. Make sure you have a firm stance and good footing. Clean up the shavings as they get in the way.





10. Regularly maintain the lathe to ensure it is sound and in good repair.





11. Dull tools do not cut well and may slip. Sharpen often. A good thing to remember is to sharpen to keep a tool sharp, not to regrind a dull tool.





12. Use good lighting in the work area.





13. If tired, rest. Do not use the lathe when tired or when using alcohol or drugs.





14. Beware of electric shock. Electric cords need to be in good repair and the lathe should not be used under wet condition.





15. Make sure all wrenches, chuck adjusting tools and other loose objecs are removed before turning on the lathe.





16. Never leave the lathe running unattended, even if only turning around for another tool.





Remember that the work is not over until a piece is sanded and a finish is applied. Sanding will generate an amazing amount of dust that is harmful to your lungs. A simple sanding mask should be worn and if possible a dust collector used. Many popular turning finishes are safe for human consumption but others may be toxic, including the fumes. Read all directions carefully and use appropriate safety measures such as ventilation and breathing masks. Above all, be aware that people have turned wood safely for thousands of years and a few simple precautions will continue to make it safe and enjoyable.


Thursday, February 17, 2011

Wood Turning Projects - Not Only for Bowl Turners




Wood turning projects, well chosen, are wonderful learning tools for refining or developing new skills at the wood lathe. Most people who take up the craft of wood turning begin with spindle work, turning pieces of wood held between centers with the wood grain parallel to the bed of the lathe. After some time at this aspect of the trade, they move on to faceplate work with the wood held in a chuck or faceplate and the grain running perpendicular to the bed of the lathe. While the skills are similar in each case, there are enough differences that the face plate turner may begin with a series of projects to develop the necessary skills.





However, the wood turner neglects the spindle projects at peril of old skills becoming rusty and unavailable when needed. Sooner or later a friend or relative asks for a spindle to be turned or a piece of furniture requires repair. Besides which, many items such as candle sticks or lamps may call for sections turned in either style and fastened together. Wood turning projects in a spindle orientation will provide the necessary boost in keeping up old skills and refining them to an expert point.





For the intermediate or advanced turner, wood turning projects offer the plus over exercises of being an interesting way to maintain and add to skills. While simply putting a piece of wood on a lathe and seeing shavings fly from it as the wood turns to a stick with beads and coves may seem magic to a novice, it is old hat to an accomplished turner who yet needs to refresh an aptitude acquired some time ago. Consider on the other hand a simple candle stick made with base and stem.





First of all it may be easily made of local hardwood and thus be inexpensive while at the same time beautiful. Secondly, it incorporates a variety of skills. For instance, the base can be turned faceplate style leaving a center mortise to later receive the stem. The stem now needs to be turned with a tenon on the lower end to exactly fit the mortise creating an exercise in precise fitting. In addition, a means must be found to turn a candle cup for the top of the stem that incorporates a fit for the candle, strength to hold it, and a pleasing ascetic.





As the project is repeated for the development of skills it can be made a challenge in at least two ways. First of all it may be an exercise in precise copying, always a difficulty in a craft that relies on hand and eye coordination to make each cut. Else it may become an attempt to make each one different while striving for elegance and not gaudiness, always a source of trouble in the artistic world. Plus this wood turning project and others like it point out the similarities between the two areas of wood turning and the need to learn both.


Tuesday, February 15, 2011

How To Get Started Turning Wood Pens




Although the craft of turning wood pens has been around for several decades, it recently has experienced somewhat of a revival. This is perhaps primarily due to the increased choices within the category of smaller mini-lathe power tools.





Another reason for the popularity of turning pens is the low start up investment in tools. Not only is the investment low, the tools used have a very long life span and could even be passed down to the next generation.





Listed below are the items to consider investing in to start pen turning:





o Lathe: This one should be obvious and you will find several options to choose from. The price for a new lathe will range between $100 to about $500 (all prices shown are March '08), depending on brand and features. I suggest you reading more about lathes in my ezine article reviewing the Jet Mini-lathe. In the article, I explain the process of how I chose my lathe.





o Turning Tools: I think you will need at least a gouge, parting tool, and scraper. Others may have a different list. One set of turning tools often recommended for stating out is the Harbor Freight lathe tool set that sell for less than $40. You can buy much better if you like, but this set will be more than adequate.





o Pen Mandrel: Think of the pen mandrel as a metal bar that fits between the "centers" of the lathe. The pen mandrel holds the wood blanks so you can turn them. There are several types available. I suggest you start with a collet closure mandrel, they offer a lot of flexibility when turning different lengths of blanks. You will spend about $20 or less for a good mandrel.





o Bushings: The bushings are used as a guide when turning your blanks to size for the specific pen kit you are building. You will want to buy the bushings sized for the pen you are turning. Be aware that pen kits and bushing from different manufactures may not be interchangeable. Later, when you develop more skill, you can use dial calipers to turn to size and you may choose not to use bushings at all.





o Drill Bit(s): Each style of pen will use a specific size drill bit to drill the hole for the brass tube. The most common is a 7mm used in the Slimline style. You can buy the drill bits individually or in a set. A set that many people use is a set of number, letter, and fractional drill bits from Harbor Freight. With a conversion chart, you will be able to find almost any size bit needed in this set. They often are found on sale at Harbor Freight for less than $40.





o Drill press or hand drill: Not much to say here, you are going to need something to turn the drill bits you bought. I've used a small bench drill press (less than $50) before and it worked fine. A hand drill will do, you just have to have a steady hand!





o Saw: Either a table, band, or a miter saw will work. The table saw and band saw are especially useful if you choose to cut you own pen blanks. Plan on spending a few bucks here, you and your budget will be the guide on this one. For more information on cutting your own pen blanks, see my ezine article on the subject.





o Clamps or bench vise: You will need something to press or squeeze the pen kit together. I've also used the bench drill press for this step.





o Pen Mill: This is a specialized tool, used to square your blanks after drilling and gluing in your tubes. You most likely will purchase the pen mill from the same place you ordered your kits. It will run about $20. Be aware there are several sizes of pilots available for the different pen kits or consider a complete kit with cutters and pilot shafts of different sizes. Usually the complete kit will be less expensive that buying the individual pilot shafts.





o Miscellaneous items: From here, we could go on and on. For starters you will need pen kits, pen blanks, CA (super) glue, and various grits of sandpaper. Likely, you will find you need other small items as you go, but these won't usually cost a lot of money.





For many of the larger more expensive items check eBay or Craig's List. Often you will find tools listed for sale at good prices on those web sites.





With this list, you will be well on your way to an exciting and enjoyable hobby that will last a lifetime. In addition, don't forget that with these tools not only will you be turning pens, but also bowls and other craft items. Indeed, it could even turn into additional part time income.





So what are you waiting for? Go ahead and get started.


Wood Turning - Recreation and Creation Reducing a World of Stress




In today's world of growing and ongoing stress, wood turning allows for a time to relax and to enjoy a time of recreation without all the tensions that surround us on a daily basis. Also, it permits a time of creation in what for many has become an existence of familiarity with too many things in the rat race of competitive business. To put it simply, wood turning is a hobby that opens the world of both recreation and creativity to a stressed and tired population.





One of the great stresses that inflict us in the western world with our unpredictable economy is the uncertainty of income and the need for recreation without undo cost. For woodworkers in general, the costs keep coming in the sheer rising value of lumber. Wood turners do not have this problem because they like to work with local woods in forms that are very inexpensive and sometimes free. While a cord of firewood will keep many a hobby turner busy for more than a year, it costs less money than a traditional woodworker would spend to build a table or a luthier to make a guitar.





Many wood lathes are available for less than the cost of a table saw and basic tools may be had for less than the cost of a couple of good table saw blades. All that is left is a means to sharpen those tools and most woodworkers will already have the necessary grinder. Safety goggles should be worn by woodworkers on the lathe as well as on all other power tools.





With sharp woodturning tools in hand, there is now the question of approaching the tool. Working with a wood lathe is different from other power tools in the woodworking shop. In most cases wood it manoeuvred, often awkwardly, into a moving blade or cutter. This is an inherent danger and stress producer in its own right. At the wood lathe, the opposite happens.





Wood is mounted to the lathe and made to turn. The tool rest of the lathe is placed so that any branch stubs or other protrusions from the wood miss it as the wood rotates. Otherwise the wood simply can not move. As the tools are held in the turner's hands, the cutting edge advances to the wood while the hands remain behind the tool rest. Danger is removed from the process and stress leaves.





Finally, there is the difficulty that most woodworkers face concerning the need to produce a high quality item from expensive woods. Woodturners have no such worries unless they have gone out of their way to purchase expensive woods for a project that they are sure they can achieve. Practise with inexpensive woods is easy, fun and stress free. Besides, many times a wood turner starts with fire wood and at the worst is left with a piece of fine kindling.





With all those stresses removed, there is now the opportunity for a wood turner to settle down to some peaceful moments of creating a lovely piece of wood work in the midst of great recreation.


Monday, February 14, 2011

Wood Turning Lathe - Is Bigger Better?




Wood turning lathes seem to be machines on steroids some days. They are getting bigger and more massive all the time. This is likely in response to two trends in the wood turning world. First is the response from manufacturers to a tendency among turners to make bigger and bigger pieces. Second is the prevailing idea that bigger is always better in almost every part of life. Sometimes it is just not so.





Ed Moulthrop was likely not the first to turn large pieces but he became famous for them in the twentieth century. His yard would be filled with huge sections of tree trunk more than three feet in diameter, awaiting their turn on his home made lathe. Most of them would be arranged on a slope above the shop to make them easier to manage when trying to get them indoors. He had to use a block and tackle to get them to and on the lathe and the lathe was home made to get something big enough and slow enough to turn them safely.





Here we get an idea of what the turner of large pieces of wood has to contend with each time a piece goes on the lathe. Wood is heavy and the hardwood that most turners work with is heavier still. When you consider that most of us start with green wood, the weight is even greater. How many people will really want to wrestle with a chunk of wood more than 150 pounds in weight each time they wish to turn? That is a section of log big enough to turn a 24 inch bowl. A 24 inch hollow form will easily start at 300 pounds for the blank. Considering that some turners turn upwards of four foot diameter bowls, the weight is considerable. In maple the blank, assuming you could find a tree 4 feet in diameter, would be about 1200 pounds.





For the average turner, if such a person exists, a big bowl tends to be 12 inches in diameter and for the beginner, 10 inches is a good size. It will hold a lot of salad, is large enough to handle, and can appear more intimidating than it needs to be. Many beginner level lathes will handle a 10 to 11 inch bowl and will generally serve for several years to come.





What is important for the beginner is to obtain a lathe. Be sure it is sturdy enough to use with safety and enjoyment. Wood turning is growing quickly and wood turning lathes for beginners are becoming popular with the manufacturers. This is a good time to begin your enjoyment with a wood turning lathe.


Friday, January 28, 2011

Sharpening Wood Turning Tools - Relax To A Great Edge




One of the great secrets to sharpening woodturning tools lies not in the grinder nor the tool but in the woodturner. It is learning to relax and let the tools do the work.





When one begins to turn wood, there is a lot to learn at the wood lathe, which tools to use for what cuts, how to mount the wood safely, how to make a cut that leaves a good surface and how to sharpen the tools, among others. The most arcane appearing to most newcomers to the craft is sharpening, perhaps because it takes place at the grinder and not the wood lathe itself.





However, what one quickly learns at the wood lathe is a tense turner is a tired turner. The best cuts are made with the tool held lightly but firmly in the securing hand while addressing the wood with the guiding, not clenching, hand. Legs are spread about shoulder width apart with the knees slightly bent and the leading leg the same as the guiding hand. This allows the back to be slightly curved but not rigid and the cuts to be guided rather than forced. Work goes ahead without undue effort and the tools do the work rather than being forced by tiring muscles.





All of this seems to be forgotten at the grinder. Yet the movements and body stance to sharpen the woodturning tools are or should be the same as those in turning the wood. With the grinder at the same height as the wood lathe and the tool rest in much the same position, movements that cut wood will now sharpen the tools. Tension on the part of the turner will, however, provided forced and jerking movements that will ruin and edge.





To sharpen free hand it is necessary to duplicate the hand and leg stances of the wood turning. The tool is allowed to ride the bevel along the grindstone and the handle raised as if for a cut. When sparks are observed coming over the edge the tool is rolled left and right as is for a cut. This results in a good edge without tension. Because of this relaxation, not only is a better edge developed, but the turner is also more likely to sharper often without facing all the nervousness of the grinder.





Sharpening jigs serve to eliminate a lot of the tension early because the possibility of error is greatly reduced. They also eliminate the need to learn new sharpening skills at the same time as new woodturning skills. Regardless, a better edge will be received from using the jig if the use is done in a relaxed manner.





Woodturning is intended to be enjoyable. Relaxing and enjoying the sharpening as well as the cutting will develop an all round pleasant experience in the woodworking shop.


Tuesday, January 25, 2011

Sharpening Wood Turning Tools - 7 Things to Keep In Mind




Woodturning is one of the most basic of crafts and the requirements are simple; a wood lathe to hold the work and make it spin, wood to shape and tools to cut the wood. This is woodworking at its most basic. In order to also make it among the most enjoyable of woodworking crafts is that most basic of wood cutting needs, sharp tools. There are a few things to keep in mind when sharpening wood turning tools.





First is the edge that is sought after. Many wood workers seek to sharpen a knife, chisel or plane blade to a razor edge for a clean cut and lovely shaving. However the wood for a typical woodworker stays still while the blade cuts. At the wood lathe the opposite occurs, wood spins and the tool is guided to the cut. The spinning wood, often with bark, knots and perhaps included grit rapidly ruins a razor edge. So the edge sought is one that works well but is not so sharp as to disappear.





Second is the equipment needed. Woodworkers often get a beautiful edge with various stones while woodturners are more at home with a good tool grinder. Most of the time the tool will be sharpened at the grinder and presented to the wood. A good wheel made of aluminum oxide with a grit of 80 to 100 will give a serviceable edge with a good surface left on the wood.





Third is the skill needed to sharpen that array of woodturning tools. Many woodworkers will need to sharpen straight edges with the possible foray into sharpening saws and wood carving gouges. Woodturners have tools with blades straight, curved, round, and fluted. Many have angles of sharpening that vary along the curved edge. While being able to sharpen freehand is a great asset, sharpening guides are wonderful assets to both the professional and the amateur.





Fourth is the frequency of sharpening. While the person who has learnt how to sharpen a knife well will find themselves infrequently going to the sharpening bench, a woodturner may find themselves at the tool grinding machine every couple of minutes. This makes a difference as to how a person sets up the shop to prevent too many footsteps between the wood lathe and the grinder.





Fifth comes the selection of tools. Principally they are made of three materials for the blades, high carbon steel, high speed steel and specialty steels. For all intents and purposes, most turners use the high speed steels. They will hold an edge longer than high carbon and are significantly cheaper than the specialties. A grinder with that aluminum oxide wheel will do a good job on them and will be adequate for each of the others, especially when using a sharpening jig.





Sixth is the consideration of what cuts are required by the tool. This may mean that some otherwise identical tools need to be sharpened with different configurations. Turning wood bowls is an excellent example. Some cuts are best performed with a bowl gouge sharpened straight across at a forty five degree angle. Others need a similar bowl gouge but shaped to have long wings and an angle varying from about seventy degrees at the tip to forty five along the edges. Again, a sharpening jig simplifies the sharpening process.





Seventh and perhaps most important is learning to relax while sharpening the various tools. If a poor edge or the wrong angle is obtained, it is a simple matter to return to the tool grinder and fix it. Tension is more likely to ruin an edge than is poor technique. Besides, woodturning is meant to be fun. Relaxing and enjoying such a large part of the process only adds to the amusement. Once again, consider making or buying a sharpening jig to add to the joy of woodturning.





Sharpening woodturning tools is a skill accessible to everyone who wishes to turn wood or work with a wood lathe. There are a few things to keep straight but as in all things with wood turning, practise may not make perfect but it goes a long way to getting great results.


  © Blogger template The Professional Template II by Ourblogtemplates.com 2009

Back to TOP